|
FFmpeg
|
All Data Structures Namespaces Files Functions Variables Typedefs Enumerations Enumerator Macros Groups Pages
|
FFmpeg
|
AAC encoder twoloop coder. More...
#include <float.h>#include "libavutil/mathematics.h"#include "mathops.h"#include "avcodec.h"#include "put_bits.h"#include "aac.h"#include "aacenc.h"#include "aactab.h"#include "aacenctab.h"Go to the source code of this file.
Macros | |
| #define | NOISE_LOW_LIMIT 4000 |
| This file contains a template for the twoloop coder function. More... | |
| #define | sclip(x) av_clip(x,60,218) |
Functions | |
| static int | ff_pns_bits (SingleChannelElement *sce, int w, int g) |
| static void | search_for_quantizers_twoloop (AVCodecContext *avctx, AACEncContext *s, SingleChannelElement *sce, const float lambda) |
| two-loop quantizers search taken from ISO 13818-7 Appendix C More... | |
AAC encoder twoloop coder.
Definition in file aaccoder_twoloop.h.
| #define NOISE_LOW_LIMIT 4000 |
This file contains a template for the twoloop coder function.
It needs to be provided, externally, as an already included declaration, the following functions from aacenc_quantization/util.h. They're not included explicitly here to make it possible to provide alternative implementations:
Definition at line 54 of file aaccoder_twoloop.h.
Referenced by mark_pns(), search_for_pns(), and search_for_quantizers_twoloop().
| #define sclip | ( | x | ) | av_clip(x,60,218) |
Definition at line 56 of file aaccoder_twoloop.h.
|
inlinestatic |
Definition at line 59 of file aaccoder_twoloop.h.
Referenced by search_for_quantizers_twoloop().
|
static |
two-loop quantizers search taken from ISO 13818-7 Appendix C
rdlambda controls the maximum tolerated distortion. Twoloop will keep iterating until it fails to lower it or it reaches ulimit * rdlambda. Keeping it low increases quality on difficult signals, but lower it too much, and bits will be taken from weak signals, creating "holes". A balance is necesary. rdmax and rdmin specify the relative deviation from rdlambda allowed for tonality compensation
sfoffs controls an offset of optmium allocation that will be applied based on lambda. Keep it real and modest, the loop will take care of the rest, this just accelerates convergence
zeroscale controls a multiplier of the threshold, if band energy is below this, a zero is forced. Keep it lower than 1, unless low lambda is used, because energy < threshold doesn't mean there's no audible signal outright, it's just energy. Also make it rise slower than rdlambda, as rdscale has due compensation with noisy band depriorization below, whereas zeroing logic is rather dumb
Psy granted us extra bits to use, from the reservoire adjust for lambda except what psy already did
Constant Q-scale doesn't compensate MS coding on its own No need to be overly precise, this only controls RD adjustment CB limits when going overboard
When using a constant Q-scale, don't adjust bits, just use RD Don't let it go overboard, though... 8x psy target is enough
Don't offset scalers, just RD
search further
and zero out above cutoff frequency
Scale, psy gives us constant quality, this LP only scales bitrate by lambda, so we save bits on subjectively unimportant HF rather than increase quantization noise. Adjust nominal bitrate to effective bitrate according to encoding parameters, AAC_CUTOFF_FROM_BITRATE is calibrated for effective bitrate.
Compensate for extensions that increase efficiency
for values above this the decoder might end up in an endless loop due to always having more bits than what can be encoded.
XXX: some heuristic to determine initial quantizers will reduce search time determine zero bands and upper distortion limits
Compute initial scalers
log2f-to-distortion ratio is, technically, 2 (1.5db = 4, but it's power vs level so it's 2). But, as offsets are applied, low-frequency signals are too sensitive to the induced distortion, so we make scaling more conservative by choosing a lower log2f-to-distortion ratio, and thus more robust.
Clip
Scale uplims to match rate distortion to quality bu applying noisy band depriorization and tonal band priorization. Maxval-energy ratio gives us an idea of how noisy/tonal the band is. If maxval^2 ~ energy, then that band is mostly noise, and we can relax rate distortion requirements.
psy already priorizes transients to some extent
In ABR, we need to priorize less and let rate control do its thing
In ABR, we need to priorize less and let rate control do its thing
PNS isn't free
Must recompute distortion
PNS isn't free
Start with big steps, end up fine-tunning
Um... over target. Save bits for more important stuff.
SF difference limit violation risk. Must re-clamp.
Scout out next nonzero bands
Make sure proper codebooks are set
Cannot zero out, make sure it's not attempted
Check that there's no SF delta range violations
Set global gain to something useful
Definition at line 67 of file aaccoder_twoloop.h.
Referenced by ff_aac_coder_init_mips().
1.8.6